22/03/25
Brief analysis of the application of oil transfer pump
The normal applicable temperature of the oil pump is within 250 degrees. If it needs to transport high temperature medium, it can be customized as a high temperature type.
The normal applicable temperature of the oil pump is within 250 degrees. If it needs to transport high temperature medium, it can be customized as a high temperature type.
The oil transfer pump is suitable for conveying lubricating oil with no solid particles and fibers, non-corrosive, temperature not higher than 250℃, viscosity of 5×10-6～1.5×10-3m2/s (5-1500cSt) or similar lubrication Oil and other liquids, as well as for hydraulic transmission systems. Oil pump flow: 1-58 cubic meters per hour. High temperature pump is suitable for conveying medium with high temperature and no impurities. It adopts mechanical seal and packing seal. It is used in plastic and rubber processing industry.
How to operate
The method of making diesel generator sets more fuel-efficient, reducing the water temperature. The water temperature of agricultural diesel engines is generally lower than 45 °C, so that the diesel cannot be completely burned, the viscosity of the oil is large, and the running resistance is increased. water temperature.
Ensure that the machine does not leak oil. Diesel engine oil pipelines often have loopholes due to uneven joint surfaces, deformation or damage of gaskets. The solution is: apply the valve paint to the gasket and put it on the glass plate and grind it flat to correct the oil pipe joint; add a diesel recovery device, and use a plastic pipe to connect the oil return pipe on the oil nozzle with the hollow screw, so that the return oil flows into the fuel tank.
RELEVANT
22/03/25
The development direction of hot oil pump is small pulsation
In order to improve the performance of hot oil pump and reduce the manufacturing cost, it is required to meet the design requirements of smaller volume, faster response, smaller pulsation and lower noise of hot oil pump.
VIEW ALL
22/03/25
High pressure multistage diesel pump classification
Open or half open in high pressure multistage diesel pump is generally adopts the volute pump body, pump casing in main shaft centerline plane separately, the pump according to the main shaft is installed in the open in different points level and vertical open type two kinds, it is each impeller has a corresponding volute suction chamber and pressure out of the room, which is equivalent to a few single stage volute pump assembly work on the same shaft series.
VIEW ALL
22/02/21
What are the common reasons for the failure of the oil pump
Generally speaking, the mechanical oil transfer pump is very reliable. Even if it fails, it is often the diaphragm rupture that causes insufficient oil transfer. Sometimes the rocker arm or spring of the oil pump is worn out excessively, which will also cause insufficient oil delivery. The fault is easier to identify. The old-fashioned oil pump can be repaired, but the new-style oil pump cannot be disassembled, so it should be replaced once it fails.
VIEW ALL
22/02/21
Analysis of the types of oil transfer pumps
Scope of application of KCB oil transfer pump: It is suitable for conveying lubricating oil or other liquids with similar properties to lubricating oil that do not contain solid particles and fibers, are non-corrosive, have a temperature not higher than 150 °C, and have a viscosity of 5 to 1500 cst.
VIEW ALL
22/02/21
Hot oil pump bearing lubrication
the bearing oil level is too low, so that some parts of the RY hot oil pump bearing can not be lubricated, so the bearing will produce wear and heat, so that the bearing is burnt out.
VIEW ALL
22/02/21
Common faults and countermeasures of electric grease gun
The electric grease gun is a miniature electric grease gun, which consists of a casing, a frame, a plunger pump mechanism, a crank-slider mechanism, a gear reduction mechanism, an oil supply system, an operating system and a power system: its structure is small and the battery is built-in, An external charger can be installed, driven by a DC motor, the price is moderate, labor-saving, fast, easy to operate, high pressure, and can meet the general mechanical oiling requirements.
VIEW ALL
22/02/21
Precautions and maintenance when using electric grease gun daily
Before use, check whether the valve spring, steel ball and other parts are in short supply, the sealing condition of the piston and the oil gun head, and pay attention to check the squeezing effect to ensure the smooth progress of the maintenance work.
VIEW ALL
