22/02/21

Analysis of the types of oil transfer pumps


Scope of application of KCB oil transfer pump: It is suitable for conveying lubricating oil or other liquids with similar properties to lubricating oil that do not contain solid particles and fibers, are non-corrosive, have a temperature not higher than 150 °C, and have a viscosity of 5 to 1500 cst.

Introduction of various fuel pumps

1. kcb oil pump

Scope of application of KCB oil transfer pump: It is suitable for conveying lubricating oil or other liquids with similar properties to lubricating oil that do not contain solid particles and fibers, are non-corrosive, have a temperature not higher than 150 °C, and have a viscosity of 5 to 1500 cst.

2. 2CY oil pump

Scope of application of 2CY oil transfer pump: 2CY oil transfer pump is suitable for conveying lubricating oil or other liquids with similar properties to lubricating oil without solid particles and fibers, non-corrosive, temperature not higher than 200 ℃, viscosity of 5-1500 cst, and suitable for Hydraulic transmission system.

3. KCG oil pump

KCG high temperature oil pump application: plastic and rubber processing industry, textile printing and dyeing industry, coating industry, wood processing industry, food industry, papermaking and printing and other industries such as heating and transmission of liquid heat carrier heating carrier.

4. 2CG oil pump

2CG oil pump is used for conveying and pressurizing medium such as residual oil, coal tar, floor oil, foam raw materials and additives. It is an ideal conveying and pressurizing equipment for glass, foam, building materials, chemical construction, petroleum, grain and oil industries.

5. RCB oil pump

RCB oil pump application: used to transport heavy oil, asphalt, glue, resin, detergent, etc. Scope of application of RCB oil pump: It is suitable for conveying non-corrosive, solid particles and solidifying medium at room temperature. It is especially suitable for outdoor installations in alpine regions and occasions where the medium needs to be kept warm during the process. The medium temperature can reach 250°C and the viscosity is 5-1500cst.

6. YCB oil pump

Scope of application of YCB oil transfer pump: This oil transfer pump is suitable for conveying lubricating oil with no solid particles and fibers, non-corrosive, temperature not higher than 80℃, viscosity of 5-1500cst or other liquids with similar properties to lubricating oil.


RELEVANT


22/02/21

What are the common reasons for the failure of the oil pump

Generally speaking, the mechanical oil transfer pump is very reliable. Even if it fails, it is often the diaphragm rupture that causes insufficient oil transfer. Sometimes the rocker arm or spring of the oil pump is worn out excessively, which will also cause insufficient oil delivery. The fault is easier to identify. The old-fashioned oil pump can be repaired, but the new-style oil pump cannot be disassembled, so it should be replaced once it fails.

VIEW ALL

22/02/21

Hot oil pump bearing lubrication

the bearing oil level is too low, so that some parts of the RY hot oil pump bearing can not be lubricated, so the bearing will produce wear and heat, so that the bearing is burnt out.

VIEW ALL

22/02/21

Common faults and countermeasures of electric grease gun

The electric grease gun is a miniature electric grease gun, which consists of a casing, a frame, a plunger pump mechanism, a crank-slider mechanism, a gear reduction mechanism, an oil supply system, an operating system and a power system: its structure is small and the battery is built-in, An external charger can be installed, driven by a DC motor, the price is moderate, labor-saving, fast, easy to operate, high pressure, and can meet the general mechanical oiling requirements.

VIEW ALL

22/02/21

Precautions and maintenance when using electric grease gun daily

Before use, check whether the valve spring, steel ball and other parts are in short supply, the sealing condition of the piston and the oil gun head, and pay attention to check the squeezing effect to ensure the smooth progress of the maintenance work.

VIEW ALL