22/03/25
The development direction of hot oil pump is small pulsation
In order to improve the performance of hot oil pump and reduce the manufacturing cost, it is required to meet the design requirements of smaller volume, faster response, smaller pulsation and lower noise of hot oil pump.
Trends in research
In order to improve the performance of hot oil pump and reduce the manufacturing cost, it is required to meet the design requirements of smaller volume, faster response, smaller pulsation and lower noise of hot oil pump.
In addition to consolidating its existing advantages on the basis of the main development direction of hot oil pump.
Small flow pulsation
The pulsation of the flow may cause the hydraulic system to vibrate, produce noise and work unsteadily.
The pulsation of flow always coexists with the pulsation of pressure. The periodical change of the radial force of the gear will also affect the life of the shaft and the bearing.
High pressure
Many hydraulic systems have high pressure requirements, which is the biggest advantage of hot pumps compared with other pumps.
Traditional hot oil pump is affected by structure, material, processing technology and other factors to improve the pressure of hot oil pump is very difficult, now the most important way to achieve high pressure is to innovate in the structure.
Large displacement
Some hydraulic systems require large displacement, but it is difficult to improve the displacement of hot oil pump due to the influence of the structure. Large displacement can be achieved by increasing the tooth thickness, reducing the number of teeth and speeding up the speed.
Adjustable displacement hot oil pump
Many hydraulic systems require adjustable displacement, which is conducive to the accurate control of the hydraulic system.
There are many researches on adjustable displacement hot oil pump, but few of them are transformed into products.
Adjustable displacement hot oil pump is one of the most important research directions in the future.
Low noise
In modern industry, people put forward higher requirements for the working environment, and reducing the noise of hot oil pump has also become a very important research direction, mainly through reducing the mechanical noise and the noise of liquid oil.
Mechanical noise has a great relationship with gear meshing and machining accuracy.
The noise of liquid oil is mainly to reduce the trapped oil of hot oil pump through reasonable structural design.
Relatively speaking, internal meshing hot oil pump has greater advantages in stability and noise control.
RELEVANT
22/03/25
High pressure multistage diesel pump classification
Open or half open in high pressure multistage diesel pump is generally adopts the volute pump body, pump casing in main shaft centerline plane separately, the pump according to the main shaft is installed in the open in different points level and vertical open type two kinds, it is each impeller has a corresponding volute suction chamber and pressure out of the room, which is equivalent to a few single stage volute pump assembly work on the same shaft series.
VIEW ALL
22/02/21
What are the common reasons for the failure of the oil pump
Generally speaking, the mechanical oil transfer pump is very reliable. Even if it fails, it is often the diaphragm rupture that causes insufficient oil transfer. Sometimes the rocker arm or spring of the oil pump is worn out excessively, which will also cause insufficient oil delivery. The fault is easier to identify. The old-fashioned oil pump can be repaired, but the new-style oil pump cannot be disassembled, so it should be replaced once it fails.
VIEW ALL
22/02/21
Analysis of the types of oil transfer pumps
Scope of application of KCB oil transfer pump: It is suitable for conveying lubricating oil or other liquids with similar properties to lubricating oil that do not contain solid particles and fibers, are non-corrosive, have a temperature not higher than 150 °C, and have a viscosity of 5 to 1500 cst.
VIEW ALL
22/02/21
Hot oil pump bearing lubrication
the bearing oil level is too low, so that some parts of the RY hot oil pump bearing can not be lubricated, so the bearing will produce wear and heat, so that the bearing is burnt out.
VIEW ALL
22/02/21
Common faults and countermeasures of electric grease gun
The electric grease gun is a miniature electric grease gun, which consists of a casing, a frame, a plunger pump mechanism, a crank-slider mechanism, a gear reduction mechanism, an oil supply system, an operating system and a power system: its structure is small and the battery is built-in, An external charger can be installed, driven by a DC motor, the price is moderate, labor-saving, fast, easy to operate, high pressure, and can meet the general mechanical oiling requirements.
VIEW ALL
22/02/21
Precautions and maintenance when using electric grease gun daily
Before use, check whether the valve spring, steel ball and other parts are in short supply, the sealing condition of the piston and the oil gun head, and pay attention to check the squeezing effect to ensure the smooth progress of the maintenance work.
VIEW ALL
